SSSAJ Journal of Natural Resources and Life Sciences Education
HOME HELP FEEDBACK SUBSCRIPTIONS ARCHIVE SEARCH TABLE OF CONTENTS
QUICK SEARCH:   [advanced]


     

This Article
Right arrow Abstract Freely available
Right arrow Figures Only
Right arrow Full Text (PDF) Free
Right arrow Alert me when this article is cited
Right arrow Alert me if a correction is posted
Services
Right arrow Similar articles in this journal
Right arrow Similar articles in ISI Web of Science
Right arrow Alert me to new issues of the journal
Right arrow Download to citation manager
Right arrow reprints & permissions
Citing Articles
Right arrow Citing Articles via HighWire
Right arrow Citing Articles via ISI Web of Science (7)
Right arrow Citing Articles via Google Scholar
Google Scholar
Right arrow Articles by Ren, T.
Right arrow Articles by Ju, Z.
Right arrow Search for Related Content
PubMed
Right arrow Articles by Ren, T.
Right arrow Articles by Ju, Z.
Agricola
Right arrow Articles by Ren, T.
Right arrow Articles by Ju, Z.
Related Collections
Right arrow Soil Thermal Properties
Right arrow Water Content
Right arrow Soil Methods/Instrumentation
Published in Soil Sci. Soc. Am. J. 67:1631-1634 (2003).
© 2003 Soil Science Society of America
677 S. Segoe Rd., Madison, WI 53711 USA

DIVISION S-1—SOIL PHYSICS

Heat-Pulse Method for Soil Water Content Measurement

Influence of the Specific Heat of the Soil Solids

T. Rena, T. E. Ochsnerb, R. Horton*,b and Z. Juc

a Institute of Geographic Sciences and Natural Resources Research, Chinese Academy of Sciences, Beijing, China 100101
b Dep. of Agronomy, Iowa State Univ., Ames, IA 50011
c China Agricultural Univ., Beijing, China 100094

* Corresponding author (rhorton{at}iastate.edu).


   ABSTRACT
TOP
 NOTES
 ABSTRACT
INTRODUCTION
 THEORY
 MATERIALS AND METHODS
 RESULTS AND DISCUSSION
 CONCLUSIONS
 REFERENCES
 
The heat-pulse method measures soil volumetric water content ({theta}) based on the linear relationship between soil volumetric heat capacity (C) and {theta}. Previous work suggested that this method was more appropriate for determining change of {theta} rather than its absolute value. In this study, we demonstrate that the heat-pulse method can give accurate {theta} estimation when values for the specific heat of the soil solids (cs) are determined using the heat-pulse method. Heat-pulse measurements were performed on packed columns of three soils with a wide range of bulk density ({rho}b) and {theta}. When the commonly used cs value (0.725 kJ kg-3 K-1) was used, the heat-pulse method overestimated {theta} by 0.052 m3 m-3 on average. However, when cs values determined from heat-pulse measurements on oven-dried soil were used, the heat-pulse method provided accurate {theta} results (-0.006 m3 m-3 average error). Using soil-specific, heat-pulse determined cs values also reduced the average root mean square error (RMSE) in {theta} for the three soils from 0.061 to 0.039 m3 m-3.

Abbreviations: C, soil volumetric heat capacity • cs, specific heat of soil solids • RMSE, root mean square error • {theta}, soil volumetric water content • {rho}b, bulk density • {rho}w, density of water


   INTRODUCTION
TOP
 NOTES
 ABSTRACT
 INTRODUCTION
THEORY
 MATERIALS AND METHODS
 RESULTS AND DISCUSSION
 CONCLUSIONS
 REFERENCES
 
RECENTLY, the heat-pulse method has been used to measure {theta}. Laboratory and field studies (Bristow et al., 1993; Tarara and Ham, 1997; Song et al., 1998) indicated that the method offers the benefits of low cost, less soil disturbance, and automatic and frequent in situ readings. The small sample volume also makes this method suitable for detailed measurements of the spatial variability of {theta}.

Several factors, including probe spacing (Bristow et al., 1993), soil bulk density (Tarara and Ham, 1997), and soil mineralogy (Bristow, 1998) may affect the accuracy of {theta} measurement using the heat-pulse method. Bristow et al. (1993) and Tarara and Ham (1997) concluded that this method could provide accurate measurements of changes in {theta}. In this note, we demonstrate that the accuracy of {theta} measurement with the heat-pulse method is improved by using soil-specific values for cs.


   THEORY
TOP
 NOTES
 ABSTRACT
 INTRODUCTION
 THEORY
MATERIALS AND METHODS
 RESULTS AND DISCUSSION
 CONCLUSIONS
 REFERENCES
 
The measurement of C with the heat-pulse method relies on the theory of radial heat conduction of a short-duration heat pulse away from an infinite line source. In an infinite medium, the temperature change as a function of time at a radial distance from the heat-pulse source is given by (de Vries, 1952; Kluitenberg et al., 1993),

[1]
where {Delta}T is the temperature change (°C), t is time (s), t0 is the duration of the heat pulse (s), r is the radial distance (m), q is the rate of heating (W m-1), {alpha} is the soil thermal diffusivity (m2 s-1), C is the volumetric heat capacity (J m-3 K-1), and -Ei(-x) is the exponential integral (Abramowitz and Stegun, 1972). Once the {Delta}T(r, t) data are obtained from the probe, Eq. [1] is used to determine {alpha} and C by means of nonlinear regression (Bristow et al., 1995; Welch et al., 1996).

The volumetric heat capacity can also be estimated by summing the contributions of the individual components (Campbell et al., 1991):

[2]
where {rho}w is the density of water (Mg m-3), cw is the specific heat capacity of water (kJ kg-1 K-1), and {rho}b is soil bulk density (Mg m-3). The contribution of soil air to C is ignored because the density and specific heat of air are very small relative to the other terms.

Rearranging Eq. [2] yields a simple expression for determining {theta} from the heat-pulse method (Campbell et al., 1991):

[3]


   MATERIALS AND METHODS
TOP
 NOTES
 ABSTRACT
 INTRODUCTION
 THEORY
 MATERIALS AND METHODS
RESULTS AND DISCUSSION
 CONCLUSIONS
 REFERENCES
 
The heat-pulse function of a thermo-TDR probe (Ren et al., 1999) was used to measure C. The probe consists of three parallel stainless steel needles, each enclosing a line heater and a thermocouple. The rods are 1.3 mm in diameter and 40 mm in length and spaced 6 mm apart. The heaters are made from 75-µm diam. enameled Evanohm wire (Wilbur B. Driver Co., Newark, NJ), and the thermocouples were chromel constantan. The resistance of the completed heater is 887.6 {Omega} m-1. See Ren et al. (1999) for additional details regarding the probe design and construction.

The heater-to-thermocouple spacing was calibrated using agar-immobilized water (5 g agar L-1), taking heat capacity of the water as 4.18 MJ m-3 K-1 (Campbell et al., 1991). The heat pulse was generated by applying a DC current to the central heater with a direct current supply (Model HY1791-3S, Huaiyin Electronics Equip. Corp., Huaiyin, China) for 15 s. A data logger (Model CR10X, Campbell Scientific, Logan, UT) controlled the heat input, monitored the temperatures of the thermocouples every second, and recorded the voltage drop across a precision resistor that was used to determine the current applied to the heater. The heater-to-thermocouple spacing was calculated by using a nonlinear regression method (Welch et al., 1996) to fit the temperature-by-time data.

The heat-pulse method was evaluated in the laboratory on three soils: a sand, a silt loam, and a silty clay loam. Table 1 lists the major physical characteristics of the three soils. Particle-size analysis was performed using the hydrometer method (Gee and Bauder, 1986) and the soil organic matter was measured using the Walkely–Black titration method (Nelson and Sommers, 1982). The soils were air-dried, ground, sieved through a 2-mm screen, moistened with distilled water, and packed into soil columns (5.2-cm i.d. and 6.0 cm in height) with different water contents and bulk densities. Three columns with different {rho}b values were packed at each value of {theta}. The {rho}b of the soil columns ranged from 0.95 to 1.45 Mg m-3 and {theta} varied from air dry to saturation. All of the columns were tightly covered and placed in a temperature-regulated room (20 ± 1.2°C) for 48 h before measurements. After the probe was inserted into a soil column from the surface, a constant current was then applied from the direct current supply to the central heater for 15 s to generate the heat pulse. The data logger recorded the heating power by measuring the voltage drop across the precision resistor and measured the temperature in the outer rods as a function of time for 300 s. The soil volumetric heat capacity was calculated by analyzing the temperature increase versus time data at the sensor needles using a nonlinear curve-fitting technique (Welch et al., 1996). In each column, the heat-pulse measurements were repeated three times at 60-min intervals. The volumetric heat capacity was taken as the mean of the three replicate measurements. Finally, gravimetric water contents of the soils were determined by oven drying the samples at 105°C, and {rho}b of the soil columns was also determined.


View this table:
[in this window]
[in a new window]
  		Table 1. Selected properties of the soils.

 
To estimate cs in Eq. [2] and [3], we performed heat-pulse measurements for oven-dried samples of all three soils. The cs values were then calculated from the relationship C = {rho}bcs. Table 2 presents the measured results. Particle density was also determined using the pycnometer method and was used to calculate the volumetric heat capacity of the soil solids shown in Table 2.


View this table:
[in this window]
[in a new window]
  		Table 2. Particle density ({rho}s), specific heat (cs), and volumetric heat capacity ({rho}scs) of the soil solids. The values are means and standard errors of three replicates.

 

   RESULTS AND DISCUSSION
TOP
 NOTES
 ABSTRACT
 INTRODUCTION
 THEORY
 MATERIALS AND METHODS
 RESULTS AND DISCUSSION
CONCLUSIONS
 REFERENCES
 
A survey of the published data indicates a relatively wide range of values for cs (Table 3), from 0.644 kJ kg-1 K-1 (Johnston, 1937) to 0.939 kJ kg-1 K-1 (Campbell et al., 1991). Bristow (1998) showed that errors of >10% can occur in heat-pulse {theta} measurement when inaccurate values of cs were used in Eq. [3]. In this study, we first used 0.725 kJ kg-1 K-1 (de Vries, 1963) for cs and calculated {theta} from C measurements using Eq. [3]. Figure 1 presents the heat-pulse results in comparison with the values determined gravimetrically. Good linear relationships exist between the data of the heat-pulse method and the gravimetric method. However, regardless of soil texture, {theta}, and {rho}b, the heat-pulse method systematically overestimated {theta}. On average, Eq. [3] overestimated {theta} by 0.067, 0.040, and 0.050 m3 m-3 for the sand, the silt loam, and the silty clay loam, respectively. Some of the scatter of the data at {theta} > 0.2 m3 m-3 was caused by the spatial variation of {rho}b within the columns, since we experienced difficulties in packing the soil columns uniformly at higher water contents.


View this table:
[in this window]
[in a new window]
  		Table 3. Literature values of specific heat of soil solids (cs).

 


View larger version (14K):
[in this window]
[in a new window]
  		Fig. 1. Heat-pulse water content, {theta}, vs gravimetrically determined {theta}. The parameter of specific heat of soil solids, cs, was 0.725 kJ kg-1 K-1. The solid lines are the 1:1 lines.

 
We then used the cs values determined from the heat-pulse measurements on the oven-dried soils to estimate {theta} using Eq. [3]. The heat-pulse estimated cs values were 0.881, 0.913, and 0.973 kJ kg-1 K-1 for the sand, silty loam, and silty clay loam (Table 2). These values are respectively 21.5, 25.9, and 34.2% higher than the commonly used value of 0.725 kJ kg-1 K-1 (de Vries, 1963). The results calculated using these soil specific cs values agreed well with the gravimetrically measured values, and the data were randomly distributed along the 1:1 line (Fig. 2) . On average, Eq. [3] overestimated {theta} by 0.02 m3 m-3 for the sand and underestimated {theta} by 0.014 and 0.025 m3 m-3 for the silt loam and the silty clay loam, respectively. For each soil the bias of the {theta} measurement was reduced by using the cs values determined from the heat-pulse measurements on oven-dried soil.



View larger version (14K):
[in this window]
[in a new window]
  		Fig. 2. Heat-pulse water content, {theta}, vs gravimetrically determined {theta}. The heat-pulse measured specific heat of soil solids, cs, for each soil was used. The solid lines are the 1:1 lines.

 
Using the soil-specific cs values also led to decreases in the root mean square error (RMSE) of the heat-pulse {theta} measurements for each soil. The RMSE decreased from 0.073 to 0.041 m3 m-3 for the sand, from 0.046 to 0.029 m3 m-3 for the silt loam, and from 0.062 to 0.048 m3 m-3 for the silty clay loam. We suspect that non-uniformities of {rho}b and {theta} within the packed columns caused these RMSE values to be larger than they would have been if the columns had been perfectly uniform. If so, then the real precision of the heat-pulse method is likely better than that indicated by these RMSE values.

Previous investigators (Bristow et al., 1993; Tarara and Ham, 1997) concluded that the heat-pulse method could provide accurate measurements of changes in {theta}. Ours results showed that the heat-pulse method is also able to provide accurate absolute {theta} for soils with a range of textures and {rho}b, provided appropriate cs values are used. For the three soils used in this study, the measured cs values are greater than the commonly employed value, but they are still in the range of literature values (Table 3).


   CONCLUSIONS
TOP
 NOTES
 ABSTRACT
 INTRODUCTION
 THEORY
 MATERIALS AND METHODS
 RESULTS AND DISCUSSION
 CONCLUSIONS
REFERENCES
 
We demonstrate that using an inappropriate cs value leads to errors in heat-pulse measured {theta}. In this study, using the cs value (0.725 kJ kg-3 K-1) from de Vries (1963) resulted in overestimation of {theta} by 0.040 to 0.067 m3 m-3. We also illustrated that using cs values determined from heat-pulse measurements on oven-dried soil samples improves the accuracy of the heat-pulse {theta} measurements. Again, the focus of this study is on obtaining more accurate {theta} measurements by the heat-pulse technique. Independent measurements of cs would be required to determine if the cs values determined by the heat-pulse method are themselves accurate.


   NOTES
TOP
 NOTES
ABSTRACT
 INTRODUCTION
 THEORY
 MATERIALS AND METHODS
 RESULTS AND DISCUSSION
 CONCLUSIONS
 REFERENCES
 
Supported by the Natural Science Foundation of Hebei (No. 300309). Journal Paper No. J-19760 of the Iowa Agriculture and Home Economics Experiment Station, Ames, IA, Project No. 3287. Supported by the Agronomy Department Endowment Funds, Hatch Act, and the State of Iowa.

Received for publication March 7, 2002.


   REFERENCES
TOP
 NOTES
 ABSTRACT
 INTRODUCTION
 THEORY
 MATERIALS AND METHODS
 RESULTS AND DISCUSSION
 CONCLUSIONS
 REFERENCES
 




This article has been cited by other articles:


Home page
 Soil Sci.Home page
G. Liu, B. Li, T. Ren, R. Horton, and B. C. Si
Analytical Solution of Heat Pulse Method in a Parallelepiped Sample Space with Inclined Needles
Soil Sci. Soc. Am. J., September 1, 2008; 72(5): 1208 - 1216.
[Abstract] [Full Text] [PDF]

Home page
 Soil Sci.Home page
X. Liu, T. Ren, and R. Horton
Determination of Soil Bulk Density with Thermo-Time Domain Reflectometry Sensors
Soil Sci. Soc. Am. J., June 18, 2008; 72(4): 1000 - 1005.
[Abstract] [Full Text] [PDF]

Home page
 Soil Sci.Home page
O. K. Olmanson and T. E. Ochsner
A Partial Cylindrical Thermo-Time Domain Reflectometry Sensor
Soil Sci. Soc. Am. J., May 1, 2008; 72(3): 571 - 577.
[Abstract] [Full Text] [PDF]

Home page
 Vadose Zone JHome page
M. H. Young, G. S. Campbell, and J. Yin
Correcting Dual-Probe Heat-Pulse Readings for Changes in Ambient Temperature
Vadose Zone J., January 23, 2008; 7(1): 22 - 30.
[Abstract] [Full Text] [PDF]

Home page
 Soil Sci.Home page
G. Liu, B. Li, T. Ren, and R. Horton
Analytical Solution of the Heat Pulse Method in a Parallelepiped Sample Space
Soil Sci. Soc. Am. J., August 27, 2007; 71(5): 1607 - 1619.
[Abstract] [Full Text] [PDF]

Home page
 Soil Sci.Home page
J. L. Heitman, R. Horton, T. Ren, and T. E. Ochsner
An Improved Approach for Measurement of Coupled Heat and Water Transfer in Soil Cells
Soil Sci. Soc. Am. J., May 16, 2007; 71(3): 872 - 880.
[Abstract] [Full Text] [PDF]

Home page
 Vadose Zone JHome page
O. K. Olmanson and T. E. Ochsner
Comparing Ambient Temperature Effects on Heat Pulse and Time Domain Reflectometry Soil Water Content Measurements
Vadose Zone J., May 26, 2006; 5(2): 751 - 756.
[Abstract] [Full Text] [PDF]

Home page
 Vadose Zone JHome page
T. Ren, Z. Ju, Y. Gong, and R. Horton
Comparing Heat-Pulse and Time Domain Reflectometry Soil Water Contents from Thermo-Time Domain Reflectometry Probes
Vadose Zone J., November 11, 2005; 4(4): 1080 - 1086.
[Abstract] [Full Text] [PDF]

This Article
Right arrow Abstract Freely available
Right arrow Figures Only
Right arrow Full Text (PDF) Free
Right arrow Alert me when this article is cited
Right arrow Alert me if a correction is posted
Services
Right arrow Similar articles in this journal
Right arrow Similar articles in ISI Web of Science
Right arrow Alert me to new issues of the journal
Right arrow Download to citation manager
Right arrow reprints & permissions
Citing Articles
Right arrow Citing Articles via HighWire
Right arrow Citing Articles via ISI Web of Science (7)
Right arrow Citing Articles via Google Scholar
Google Scholar
Right arrow Articles by Ren, T.
Right arrow Articles by Ju, Z.
Right arrow Search for Related Content
PubMed
Right arrow Articles by Ren, T.
Right arrow Articles by Ju, Z.
Agricola
Right arrow Articles by Ren, T.
Right arrow Articles by Ju, Z.
Related Collections
Right arrow Soil Thermal Properties
Right arrow Water Content
Right arrow Soil Methods/Instrumentation

HOME HELP FEEDBACK SUBSCRIPTIONS ARCHIVE SEARCH TABLE OF CONTENTS
The SCI Journals Agronomy Journal Crop Science
Journal of Natural Resources
and Life Sciences Education		 Vadose Zone Journal
Journal of Plant Registrations Journal of
Environmental Quality		 The Plant Genome